The bolt pattern for a 2022 Ford Mustang is 5x114.3 (or 5x4.5 ), indicating that each wheel has five bolts (or lugs) that are arranged circularly with a 114.3 mm (4.5 inches) diameter.
One of the simplest yet cool 2022 Ford Mustang mods is to replace stock wheels with bigger aftermarket options.
However, before you switch, you must know your 2022 Ford Mustang lug pattern to confirm compatibility with the new set of wheels. But even if the current bolt pattern of your 2022 Ford Mustang and the new wheels do not match, consider converting to the required scheme using the wheel adapters.
Also, new rims must sit within the wheel offset range, and the 2022 Ford Mustang's stud must fit onto the hub bore. Use the measurements below while searching for new wheels.
A bolt pattern, or lug pattern, is a two-number system used to measure the imaginary circle (PCD) formed by the lug holes at the center of a wheel. The first number counts the holes in the wheel, while the second number indicates the pitch circle diameter in mm or inches.
A machined opening in the center of the wheel. It must be "Hub Centric" to reduce vibration.
The outer diameter of your wheel stud threads in either metric (M12, M14, etc.) or standard units (1/2", 9/16", etc.).
Dimensions of the stock tires, including its width, aspect ratio (sidewall), and diameter.
Dimensions of rims recommended by the manufacturer.
These wheel adapters are made of aerospace alloy aluminum 6061, T6 treatment, precision CNC machined, hard oxidation finished surface.
- Vehicle fitment compatibility is only a guide, please ensure that these are the correct ones for your vehicle.
These wheel adapters are designed to CHANGE the stock bolt pattern to an 8 x 6.5" (8 x 165.1mm) bolt pattern, allowing you to switch bolt patterns and install custom rims and tires. Positions your wheels 1.5 inches outward to correct tire rubbing issues, increase cornering stability, and allow for a more impressive stance.
*We recommend the use of a Torque Wrench to ensure proper tightening of hardware*
Included with purchase are 4 Universal Tire Valve Stem Caps precision CNC machined from Light-Weight T6 Billet Aluminum with anodized surface and rust & water-resistant polymer thread inserts to prevent rust, corrosion, and chemical damage.
Single Rear Wheel Only. Does NOT fit models with a DUALLY setup. Please note that these wheel adapters will CHANGE your vehicle's bolt pattern and are intended for use only with 8 x 165.1mm (8 x 6.5") wheels.
COMPATIBLE WITH 2000 - 2010 Chevrolet Silverado 2500HD / 3500HD (2WD 4WD) and 2000 - 2010 GMC Sierra 2500HD / 3500HD (2WD 4WD). *Does NOT fit models with DUALLY setup. Please note that these wheel adapters will CHANGE your vehicle's bolt pattern and are intended for use only with 8 x 180mm wheels.
T6 BILLET ALUMINUM WHEEL ADAPTERS (4-PIECE SET): 2 Inches Thick, M14x1.5 Studs, 130mm Center Bore Without Lip | NOTE: Spacers are lug-centric, and centered using the precision machined taper seat on the lug-nuts.
These two piece conversion type wheel adapters are used to convert 8 lug vehicle with 6.5"" (165.1mm) bolt pattern to fit wheels with 6 lug 5.5"" (139.7mm) bolt pattern. They will space out your wheels for 2-inch to help you get enough clearance for wider tires and rims. CNC machined with precision craftsmanship using 6061 T6 aerospace quality billet, featured in high load capacity and corrosion resistance. High quality studs are pre-installed. Sold as a set of 4 for all four wheels.
Important:They do NOT work on manual or locking hubs. These hubs usually stick out a few inches and will protrude outside the inner piece adapter; thus not allowing the outer piece adapter to be installed.
Specifications: M14x1.50 Thread pitch, 4.4” Overall height, 0.92” Diameter, 60-degree Conical Seat, Bulge Acorn design, anti-theft spline design. Chrome Finish. For 8-lug vehicles.<... Check price on